The IPv4Socket requires a DoubleBuffer for storage of any data it
received on the socket. However it was previously using the default
constructor which can not observe allocation failure. Address this by
plumbing the receive buffer through the various derived classes.
LocalSockets keep a DoubleBuffer for both client and server usage.
This change converts the usage from using the default constructor
which is unable to observe OOM, to the new try_create factory and
plumb the result through the constructor.
Read the appropriate registers for RTL8139, RTL8168 and E1000.
For NE2000 just assume 10mbit full duplex as there is no indicator
for it in the pure NE2000 spec. Mock values for loopback.
Previously there was no way for Serenity to send a packet without an
established socket connection, and there was no way to appropriately
respond to a SYN packet on a non-listening port. This patch will respond
to any non-established socket attempts with the appropraite RST/ACK,
letting the client know to close the connection.
In accordance with RFC 793, if the receiver is in the SYN-SENT state
it should respond to a RST by aborting the connection and immediately
move to the CLOSED state.
Previously the system would ACK all RST/ACKs, and the remote peer would
just respond with more RST packets.
Previously it was possible to leak the file descriptor if we error out
after allocating the first descriptor. Now we perform both fd
allocations back to back so we can handle the potential error when
processing the second fd allocation.
It's easy to forget the responsibility of validating and safely copying
kernel parameters in code that is far away from syscalls. ioctl's are
one such example, and bugs there are just as dangerous as at the root
syscall level.
To avoid this case, utilize the AK::Userspace<T> template in the ioctl
kernel interface so that implementors have no choice but to properly
validate and copy ioctl pointer arguments.
Right now, NE2000 NICs don't work because the link is down by default
and this will never change. Of all the NE2000 documentation I looked
at I could not find a link status indicator, so just assume the link
is up.
next_packet_page points to a page, but was being compared to a byte
offset rather than a page offset when adjusting the BOUNDARY register
when the ring buffer wraps around.
Fixes#8327.
Allocate all the RX buffers in one big memory region (and same for TX.)
This removes 38 lines from every crash dump (and just seems like a
reasonable idea in general.)
This commit converts naked `new`s to `AK::try_make` and `AK::try_create`
wherever possible. If the called constructor is private, this can not be
done, so we instead now use the standard-defined and compiler-agnostic
`new (nothrow)`.
If we are in a shared interrupt handler, the called handlers might
indicate it was not their interrupt, so we should not increment the
call counter of these handlers.
Previously we would not block the caller until the connection was
established and would instead return EPIPE for the first send() call
which then likely caused the caller to abandon the socket.
This was broken by 0625342.
These are pretty common on older LGA1366 & LGA1150 motherboards.
NOTE: Since the registers datasheets for all versions of the chip
besides versions 1 - 3 are still under NDAs i had to collect
several "magical vendor constants" from the *BSD driver and the
linux driver that i was not able to name verbosely, and as such
these are labeled with the comment "vendor magic values".
We call it E1000E, because the layout for these cards is somewhat not
the same like E1000 supported cards.
Also, this card supports advanced features that are not supported on
8254x cards.
Instead of initializing network adapters in init.cpp, let's move that
logic into a separate class to handle this.
Also, it seems like a good idea to shift responsiblity on enumeration
of network adapters after the boot process, so this singleton will take
care of finding the appropriate network adapter when asked to with an
IPv4 address or interface name.
With this change being merged, we simplify the creation logic of
NetworkAdapter derived classes, so we enumerate the PCI bus only once,
searching for driver candidates when doing so, and we let each driver
to test if it is resposible for the specified PCI device.
When attempting to write to a socket that is not connected or - for
connection-less protocols - doesn't have a peer address set we should
return EPIPE instead of blocking the thread.
